ZACplus
Oliver Schlüter
Zink-Luft Brennstoffzelle plus Recycler
Mech-Jiwe
Julian Stirling
A mechanical tester which uses a welded frame, a number of 3D-printed parts, an Arduino, and a few other simple components. The tester is fo...
Syringe Pump
Drew Portero
We created a large volume open source DIY syringe pump from commonly available and 3D printed parts that allows for high accuracy and repeat...
microscope-incubation-box
HoldenLab
Microscope incubation box for home built single molecule microscope
LED Zappelin', An open source and versatile LED controller for arbitrary spectrum visual stimulation and optogenetics during 2-photon imaging.
Maxime Zimmermann
Two-photon (2P) microscopy is a cornerstone technique in neuroscience research, but combining this technology with spectrally arbitrary ligh...
Hyperspectral scanner for natural imaging above and under water
Noora Nevala
Here, we designed and implemented a fully open source and low-cost hyperspectral scanner based on a commercial spectrometer coupled to custo...
CubeFactory2
Bernd Muschard
The CubeFactory 2 is an autonomous and portable mini factory with own energy and material supply. It embeds three modules: a 3D-printer, a p...
OpenFlexure Microscope
Richard Bowman
The OpenFlexure Microscope is a 3D printable microscope, including a precise mechanical stage to move the sample and focus the optics. The...
Test Tube Photometer
Alexander Kutschera
It consists of modular test tube holding chambers, each with a low power monochromatic light-emitting diode, and a monolithic photodiode. A ...
Open Visual Stimulator
Andre Maia Chagas
The open visual stimulator is a projector system that can take up to six different leds with any chosen wavelength and project images, video...
Actifield
Victor Kumbol
We’re building an equipment called an actimeter. At the simplest, the actimeter is used to measure and record the locomotor activity - how f...
Open Source Plate Reader
Brian Chow
OSP is a low-cost open-source plate reader built out of the [Chow Lab](http://chowlab.seas.upenn.edu/) and the [George H. Stephenson Foundat...
LightM
Alexander Kutschera
Here we work on the development of software tools and a low-cost open hardware setup to study how bacteria move.
FlyPi
Andre Maia Chagas
"Flypi" is a 3D printable all in one biology lab that can be used for state of the art experiments in neurosciences as well as for human int...
OpenFlexure Delta Stage
Richard Bowman
A delta-bot stage based on the OpenFlexure design
Fermento
fakufaku
An open-source incubator for fun and profit.
Openspritzer - an open hardware pressure ejection system for reliably delivering picolitre volumes.
Maxime Zimmermann
Designed for ease of use, robustness and low-cost, the “Openspritzer” is an open hardware “Picospritzer” as routinely used in biological lab...
Incubator
Thomas Mboa
We built an open source Incubator for biology lab in Cameroon; since most of them are under-equipped due to the high cost of lab equipment. ...
OpenFlexure Block Stage
Richard Bowman
This project is a 3D printable design that enables very fine (sub-micron) mechanical positioning of a small moving stage, with surprisingly ...
Poseidon - Open source bioinstrumentation
Lior Patcher
An easy-to-use, highly customizable, and open source syringe pump and microscope system.
Arduino Voltage Amplifier
Andre Maia Chagas
a voltage amplifier based on LM741, run with 9V batteries and shaped as an Arduino Due shield
Raspberry Pi Camera Calibration Jig
Richard Bowman
A 3D-printed jig to uniformly illuminate the Raspberry Pi camera module's sensor, for the purpose of calibrating its response to different c...
Spikeling
Tom Baden
A hardware implementation of the Izhikevich model of a spiking neuron. Understanding of how neurons encode and compute information is fundam...
AXIOM Beta
A professional digital cinema camera built around FOSS and open hardware licenses.